Printer Cartridge Common Faults and Solutions Printer Cartridge Common Faults and Solutions

Inkjet printers have become a common office and even household product. However, when using an inkjet printer, there are often problems, such as the problems associated with cartridges. The following small series on one by one to solve the problems encountered cartridge.

Fault 1. After the new ink cartridge is installed, no ink is displayed or the ink is displayed after the number of pages is printed.

the reason:

1. If the ink cartridge is not installed properly or the cartridge has not been returned to the sensing dome, it needs to be reinstalled or be used to help reset the dome.

2. The metal sheet in the print head is aging or loose and causes poor contact. It is recommended to send it to the maintenance station for repair.

3. If the cartridge is not replaced according to the prescribed procedure, the cartridge must be replaced according to the prescribed procedure.

4. If it still cannot be resolved, it is most likely that the printer's electronic memory is faulty. You need to delete the printer driver, reinstall the driver, and remove the cartridge again. Reinstall the cartridge as described above.

Fault II. After replacing the ink cartridge, a horizontal line appears during printing. When the white line or graphic color is light, color cast, blurred, or cannot be printed, check whether you have used up any ink of a certain color in the ink cartridge. Then, Consider the following reasons:

1. If the label is not torn off (ie, the yellow sticker), the air duct and air guide hole are still in the closed state, and the air cannot enter the ink cartridge. At this time, the label can be completely torn off.

2. Small bubbles remain in the ink outlet. At this time, the print head should be cleaned to discharge the small bubbles.

3, ink into the air or impurities in the print head, the solution is to start the printer automatic cleaning program to clean the print head one or more times (Note: After each cleaning must print nozzle detection pattern - test line to observe the cleaning effect). Or turn off the printer and stop using it for a few hours to see if the situation has improved. If it still does not solve the problem, we recommend sending it to you.

4. A little white line may appear, which may be caused by long-term printing and some paper with poor paper quality. The surface of the paper is covered with paper particles, and the particles may stick to the print head, resulting in some ink outlets. Blocking, at this time should be printed and cleaned, if no effect to the maintenance department overhaul.

5. If the above reasons are excluded and the cleaning program has been started to clean the print head, normal printing cannot be resumed. This may be due to the dead end of the print head (usually the print head has a lifetime of about 50-60 inks) or the printer ink pump system. error occured.

Fault 3: The main cause of jamming of the print head is that the print head has not returned to the protective cover or the new ink cartridge has not been loaded in time, causing the print head to be exposed to the air for too long. The ink remaining in the print head is blocked due to air drying and can be called up. The printer's own cleaning function is cleaned to improve. If the congestion is serious, it can only be professionally cleaned or scrapped.

Fault four, color distortion causes:

1. The lack of color of the ink cartridge means that the ink of a certain color is exhausted, and the detection by the nozzle is obvious at a glance.

2. The printer set in the computer is inconsistent with the printer currently used.

3, if none of the above reasons, please check whether it is set to save ink or resume printing.

4. Color distortion is also related to computer color management, display resolution, printer resolution, and print media.

5, The printer that is causing you to use requires two or more cartridges. Please check if the same brand is used. Because the color of the same brand ink has a good complementarity and coordination, so as to ensure the reproduction of its color.

Fault 5. The picture is rough. Not delicate or smooth.

the reason:

1, poor print media, ink easy to penetrate.

2. The set resolution is low, which reduces the print quality while increasing the speed.

3, broken line; confirmed by the nozzle detection, cleaning can be eliminated once or twice.

Failure six, self-inspection line but the color of the print image is seriously color cast, or the overall picture is very good, but in some uncertain places there will be irregular thin lines, the reason is that the printer driver or picture is infected with the virus, and the ink cartridge Regardless, reinstall the printer driver or replace the picture with a virus.

Fault 7, nozzle detection is normal, but the print is always broken.

Cause: If you carefully observe the nozzle detection pattern, it is not difficult to find some disorder of the pattern, which is caused by the print head's hemisphere. Call the print head calibration tool in the application tool one or several times until the print head is calibrated.

Fault 8. Long time transport and storage in high temperature or low temperature environment is one of the main reasons for ink cartridges to spoil or not to be out of ink. Before use, they must be used at room temperature for a period of time. Otherwise, ink may not be sprayed.

Fault 9. Unless you replace the ink cartridge, please do not open the ink cartridge at will. Otherwise, it will be easy for the air to enter the cartridge and the ink will not come out. You need to clean it several times to print normally.

Fault X. Leaking ink: A new ink cartridge on the machine, a large amount of ink leakage from the inkjet hole, pollution printer, easy to burn the motherboard, this situation is an ink cartridge quality problems, should replace the ink cartridge.